Welding Terms and Definitions: You Must Know as Mechanical Engineer!!
The list of welding terminology used in the industry is big! Yet learning the right vocabulary for welding applications is essential.
If you’re starting a welding career, you will learn a lot of welding terminology. It may seem a bit overwhelming at first, but you’ll get the hang of it during your welding training.
To get you started, here’s a compilation of the most commonly used welding terms:
Arc Welding
A general term that applies to many kinds of welding. The common denominator is using an arc to create heat. Arc welding may also use other filler materials or pressure to create a weld.
Base Metal
This has two meanings: 1) the metal that will be cut or welded; 2) in an alloy, it is the largest proportion of the metal.
Have You Considered a Career in the Skilled Trades?
Fill out the form to recieve a no obligation info packet.
Bond
The point where the welding metal is joined with the base metal.
Brazing
This welding technique uses a filler metal to create a bond. The filler metal is nonferrous and has a melting point below the melting point of the base metal.
Carbon-Arc Welding
A welding method that involves creating an arc between a carbon electrode and a metal.
Coated Electrode
The electrode is covered with flux through dipping or painting. When heat is applied, the flux produces a gas that shields the arc.
Covered Electrode
The metal electrode is covered with asbestos, flux, paper or other materials to make the arc more stable and improve the welding metal.
Critical Temperature
The temperature at which the material transitions from one crystalline form to another.
Current Density
The amount of amperes applied per square inch across a particular area.
Cutting Torch
This welding tool controls gas for preheating the metal, as well as the oxygen for cutting the metal.
Direct Current Electrode Negative (DCEN)
The metal being welded is the positive pole, and the electrode is the negative pole of the arc.
Direct Current Electrode Positive (DCEP)
DCEP is the opposite of DCEN. The welded metal is the negative pole, and the electrode is the positive pole of the arc.
Electric Arc
An electrical current that forms in the gap between two electrodes creates an electric arc.
Electrode
There are many types of electrodes used in welding. An electrode conducts the electrical current through a work piece to create the weld. Some electrodes are consumed in the welding process while others are not.
Filler Material
This is the metal that is added when making a weld.
Flame (Oxygen) Cutting
The chemical action of oxygen applied to the elements in the base metal at high temperatures cuts ferrous metals.
Flame (Oxygen) Gouging
This method is used to create a groove in the metal using an oxygen-cutting tool.
Flux
This material cleans metals to prepare them for welding.
Forehand Welding
The flare is aimed at the metal ahead of the completed weld.
Gas Carbon-Arc Welding
The weld is accomplished by an electrical arc between a carbon electrode and the welding metal. Argon or helium gas provides the shielding.
Gas Metal-Arc Welding (GMAW)
The heat from the arc produced between the electrode and the metal results in a weld. A gas like helium provides the shielding. This technique is also called Metal-Inert-Gas (MIG) welding.
Gas Tungsten-Arc Welding, GTAW
Also called Tungsten-Inert-Gas (TIG) welding, this arc welding method uses an electrode made from tungsten with inert gas.
Gas Welding
Welding type where the heat for welding comes from a gas flame.
Groove Weld
Creating this weld requires filler material that goes in the groove between two metals to join them.
Hammer Welding
Hammering two pieces of heated metal together.
Hydrogen Brazing
A type of brazing in a furnace under a hydrogen atmosphere.
Hydromatic Welding
This method is also called pressure-controlled welding. Spot welds are made in a sequence using more than one electrode under pressure.
Inert Gas
Gas that doesn’t combine chemically with metal.
Joint
The area where materials are fused together.
Kerfs
The width of a piece of metal removed by cutting.
Metal-Arc Welding
This arc welding method uses metal electrodes.
MIG Welding
See gas metal arc welding (GMAW).
Multi-Impulse Welding
Making more than one weld by using multiple pulses of electricity.
Non-Ferrous
These metals do not have any iron, such as titanium, nickel, lead, copper, bronze, brass and aluminum.
Oxyacetylene Welding
The temperature needed for welding comes from burning a combination of acetylene and oxygen.
Oxy-Natural Gas Welding
In this welding process, the heat necessary to make the weld comes from burning natural gas with oxygen.
Oxy-Hydrogen Welding
The heat source for this welding method is a mixture of oxygen and hydrogen.
Oxy-Propane Welding
The heat for welding comes from burning a mixture of oxygen and propane.
Percussive Welding
This method involves applying high temperature to the welding site, just before pressure is applied.
Plasma Arc Welding
In this welding process, a constricted arc is created between a non-consumable electrode and the weld pool or between an electrode and the constricting nozzle. Ionized Gas coming out of the torch provides the necessary shielding.
Plug Weld
A hole is cut in one piece of metal. Another piece of metal is put behind the hole, and the weld is made in the hole to connect the two pieces of metal.
Porosity
This means that gas pocket or inclusions are present in the welded material.
Pressure Controlled Welding
This welding technique creates spot or projection welds in sequence with pressure applied to the weld made by multiple electrodes.
Pressure Welding
Pressure fuses the materials.
Projection Welding
A resistance welding technique used between two surfaces or the ends of one member and the surface of another.
Pulsation Welding
The welds for each spot receive more than one electrical pulse without the electrode moving or releasing the pressure.
Resistance Welding
Heat is generated through the resistance to the electric current flowing through the circuit of which the welded metal is a part.
Root of Joint
This is the part where the materials are joined are the smallest distance from each other, which could be an area, a line or a point.
Root of Weld
The point where—when observed from a cross-section viewpoint—the bottom of the weld fuses with the base metal.
Seal Weld
The main purpose of this weld is to get a tight connection and prevent leaks.
Seam Welding
This weld forms a long line that connects joints in the welded material.
Comments
Post a Comment
"Thank you for seeking advice on your career journey! Our team is dedicated to providing personalized guidance on education and success. Please share your specific questions or concerns, and we'll assist you in navigating the path to a fulfilling and successful career."